Jump to content

Beginning work on a 1902-ish GE 16" Pancake


Recommended Posts

Posted

Hello everyone,

 

First of all, it was wonderful to meet a bunch of members at Stan's meet in Houston last weekend!

 

I am am reaching out to see if any folks on the forum can help me with a project I am very excited to work on.  I have an early 1900s GE stick mount fan, the 16" model with double bearings. This is my first GE pancake (is it really a pancake?) and one of my all-time favorite variants of the early GE fans.  

 

Like many, it was stripped of broken/unnecessary parts over the years until it was down to the bare essentials.  And even though it looks like it was left out in a scrap heap for more than a few years, the dang thing still runs!  That said, the cast iron has pitted to the point that I do not think it will restore well with glossy paint, so for now I have decided to do more of a clean and conserve than a full restoration.

 

I have a whole lot of questions, but rather than write a wall of text, I figured I'd show a few photos here and see if anyone out there has:

1) Any compatible pieces they'd consider selling, maybe something kicking around that might have been too ratty to put on a nicer fan.

2) Leads to people who might know something about the specs of certain parts.  I'm pretty handy with fabrication and restoration, but since this is my first pancake, I don't have specs for any of the parts my fan is missing.

3) Any resources that could help me to have reproduction parts fabricated (struts, cage, cylindrical switch body, etc.) 

 

Thanks to any and all!

 

Best regards, 

Anthony

 

 

IMG_2518.jpeg

IMG_2517.jpeg

IMG_2516.jpeg

IMG_2515.jpeg

IMG_2514.jpeg

  • Like 1
Posted

Starting from the motor, what's needed: oil sleeve slingee, probably GE bearing cup in the back, blades assembly (cast hub), cage/struts/screws. Base needs; plastic grommet for power cord, special formed cage bracket, OFF brass plate, Inside base; new power supply block complete with terminals, Choke coil (speeds), complete switch, 3 rubber feet. Depends on production year 1902 or 1901 fan will have 5 speeds and 2 speeds controll.

  • Like 3
Posted (edited)

Unfortunately you’ll likely have more into parts than its final value.  You’re missing a lot of high $$$ parts. 

Edited by Lane Shirey
Posted

I’m aware of the parts list, and I expect this to be a long term project.  I’m a product designer by profession, so if I can’t find originals then designing parts for fabrication is what I do for a living!

Is there anyone out there who has documented dimensions or drawings of some of these parts they’ve done for their own restoration work? Specs for speed coils, anything like that?

In regards to restoration cost vs value, I’m not overly concerned about that. If that’s a driving factor, restoration is certainly the wrong hobby 😅

  • Like 3
Posted

You can get the Speed Coil from Sartron out of Washington state I believe,  possibly Oregon.   $100 shipped the last time I checked.   Brand new.

Posted (edited)
3 hours ago, Anthony Lindsey said:

You can get the Speed Coil from Sartron out of Washington state I believe,  possibly Oregon.   $100 shipped the last time I checked.   Brand new.

Sartron Email, address, and phone # from a 2023 post below. The guy in charge was Tim James.

tjames@castools.com    114 N Main St, Newberg, OR       (503) 538-3191

Edited by Russ Huber
  • Like 1
Posted

I helped Chris Campell in the not-too-distant past to purchase this example as is from a contact of mine. I recall it had its motor tag on it. Maybe he can give you some tips and guidance on how he went about reconstructing it. 

Cake.jpg

Posted

Thank you Anthony and Russ for the Startron connection, I will certainly reach out to Tim! 

 

And Russ I appreciate the suggestion to connect with @Chris Campbell.  Chris, if you're willing I'd love to hear about your restoration.  If you were able to track down original parts, maybe you could share some photos or measurements if you would be so kind.  I'd love to see some good shots of the tag too!

Posted

There is one of those being auctioned off at Sphere Auctions this week. Currently very reasonably priced.

Posted

I'm happy to report that Sartron is still making coils, many thanks for the recommendation to give them a call.  I apologize for asking things that may have already been answered in previous posts--when I tried the forum search from my phone, next to nothing came up.  But searching from my computer shows a wealth of posts to go through.  So I'll start there, and if I can't find anything specific I may ask back here.

 

Thanks for the heads up Jim, I'll keep an eye on it.

 

Best,

Anthony

Posted

Sartron makes 5 speed donut coils for the 12" and 16" GE cake fan motors.  I purchased a 5-speed donut coil for a 12" cast base Century as well from Sartron.

  • Like 1
Posted
On 10/12/2026 at 8:26 AM, Anthony Villanacci said:

Thank you Anthony and Russ for the Startron connection, I will certainly reach out to Tim! 

 

And Russ I appreciate the suggestion to connect with @Chris Campbell.  Chris, if you're willing I'd love to hear about your restoration.  If you were able to track down original parts, maybe you could share some photos or measurements if you would be so kind.  I'd love to see some good shots of the tag too!

Hi Anthony,

Unfortunately in my situation this was my second most regretted purchase and I dumped the stump vs moving forward. Prior did pick up a few components including a repo cage badge, coil, oil slingee. Will look this week to see what remains from collected parts if you are still considering moving forward.

thanks, Chris

 

 

Posted
On 10/11/2026 at 1:51 PM, Russ Huber said:

I helped Chris Campell in the not-too-distant past to purchase this example as is from a contact of mine. I recall it had its motor tag on it. Maybe he can give you some tips and guidance on how he went about reconstructing it. 

Cake.jpg

 

5 hours ago, Chris Campbell said:

Hi Anthony, unfortunately in my situation this was my second most regretted purchase and I dumped the stump vs moving forward.

Well, that's a shame. I never heard about your discontent with the purchase. I recall it was only a stump not for high dollar. The man you purchased it from and packaged it for you goes by the name of John Kruesel and was an AFCA member up until 2017.  He is in his 70s and remains a well-liked and civic established business owner in Rochester, MN. I know if you would have contacted him or myself with your discontent back then he would have taken it seriously.

The link below goes to John's business website, and the image below is John standing in his business. I took the image years ago.

 John Kruesel's General Merchandise

 

Kruesel.jpg

Posted
10 hours ago, Chris Campbell said:

Hi Anthony,

Unfortunately in my situation this was my second most regretted purchase and I dumped the stump vs moving forward. Prior did pick up a few components including a repo cage badge, coil, oil slingee. Will look this week to see what remains from collected parts if you are still considering moving forward.

thanks, Chris

 

 

Thanks for your reply Chris though I’m sorry to hear about the turn things took with your project. I am still moving forward so if you do come across anything left over please don’t hesitate to contact me.

 

Regards,

Antony

Posted
21 hours ago, Anthony Villanacci said:

Thanks for your reply Chris though I’m sorry to hear about the turn things took with your project. I am still moving forward so if you do come across anything left over please don’t hesitate to contact me.

 

Regards,

Antony

Hi Anthony,

Sending you a message. 
 

thanks, Chris

×
×
  • Create New...